Over-Engineered Drybox
von 3DPMacGyver
Druckbare Dateien (22)
-
stlSMOOTH_ROD_SPOOL_ROLLER.STL
9 Ko · 1 092 Downloads
-
stlPIVOT_BUSHING.STL
54 Ko · 1 079 Downloads
-
stlM5_SEAL_RING.STL
54 Ko · 1 100 Downloads
-
stlSPOOL_ROLLER.STL
135 Ko · 1 082 Downloads
-
stlMAGNETIC_SILICA_CONTAINER_TOP.STL
428 Ko · 1 088 Downloads
-
stlLATCH_HOOK.STL
51 Ko · 1 081 Downloads
-
stlBEARING_CAP.STL
329 Ko · 1 082 Downloads
-
stlMAGNETIC_SILICA_CONTAINER_BASE.STL
594 Ko · 1 086 Downloads
-
stlLATCH_STRAP.STL
265 Ko · 1 084 Downloads
-
stlROLLER_SPACER.STL
82 Ko · 1 078 Downloads
-
stlTOP_HINGE_B.STL
136 Ko · 1 080 Downloads
-
stlTOP_HINGE_A.STL
136 Ko · 1 079 Downloads
-
stlLOWER_HINGE_A.STL
138 Ko · 1 081 Downloads
-
stlGASKET_TOP.STL
21 Ko · 1 080 Downloads
-
stlLOWER_HINGE_B.STL
138 Ko · 1 082 Downloads
-
stlGASKET_RIGHT.STL
19 Ko · 1 077 Downloads
-
stlDRYBOX_TOP_HALF.STL
599 Ko · 1 093 Downloads
-
stlGASKET_LOWER.STL
41 Ko · 1 080 Downloads
-
stlGASKET_LEFT.STL
19 Ko · 1 080 Downloads
-
stlDRYBOX_BOTTOM_HALF_M5_MOUNT_HOLES.STL
1.5 Mo · 1 095 Downloads
-
stlDRYBOX_BOTTOM_HALF_NO_MOUNT_HOLES.STL
1.5 Mo · 1 091 Downloads
-
stepOVER-ENGINEERED_DRYBOX_V1.STEP
5.6 Mo · 1 081 Downloads
Beschreibung
As the title says, this is an over-engineered drybox. I have uploaded 2 versions of the base; a version with no mounting holes and a version with (2) M5 clearance holes in the bottom. If you opt for the version with mounting holes there is a file named "M5 Seal Ring" you can print out of TPU to act as a seal if you want.
I printed the "pivot bushings" out of TPU to sandwich between the hinge joints. The bushings are optional but make the opening and closing of the hinge have more resistance which makes it feel much nicer.
For the 8mm rod in the spool rollers I used a section of scored up smooth rod i had laying around. You can do the same, source some 8mm rod, or print the rods...STL file is attached.
Required printed parts to build:
(1x) Drybox_Bottom Half
(1x) Drybox_Top Half
(1x) Lower Hinge A
(1x) Lower Hinge B
(1x) Top Hinge A
(1x) Top Hinge B
(1x) Gasket_Left (TPU)
(1x) Gasket_Right (TPU)
(1x) Gasket_Lower (TPU)
(1x) Gasket_Top (TPU)
(4x) Roller Spacer
(2x) Spool Roller
(1x) Latch Strap (TPU)
(1x) Latch Hook
(4x) Bearing Cap
(2x) Pivot Bushing *optional (TPU)
(2x) Smooth Rod_Spool Holder (if not using 8mm rod)**
Optional Silica Bead Container:
(1x) Magnetic Silica Container_Top
(1x) Magnetic Silica Container_Base
Hardware Required:
(1x) M5 thread, 4mm pneumatic fitting
(19x) M3 Heatset nut inserts (sized for 5mm OD x 6mm Length)
(1x) M5 Heatset nut insert (sized for 7mm OD x 6mm Length)
(4x) 608ZZ bearings
(2x) 8mm X 134mm rods (see note above; can be printed if needed)
(8x) 1/4" x 1/16" thick magnets (for silica container)
(10x) M3x8 Screws
(8x) M3x12 Screws
(1x) M3x6 Screw
I printed the two main halves out of black ABS at 0.3mm layer height. PLA or PETG will both work just fine. Hinges were printed out of PETG.
I also uploaded the STEP file incase anyone needs a reference for assembly or if you wanna modify it and do your own thing.