Raspberry Pi 4 Case

door mccawley74

Printbare bestanden (24)

  • stl

    Case_Foot.stl

    4 Ko · 3 107 downloads

    Downloaden
  • stl

    PSU_Cover_Solid.stl

    148 Ko · 3 051 downloads

    Downloaden
  • stl

    PSU_Cover_Sloted.stl

    161 Ko · 3 045 downloads

    Downloaden
  • stl

    case_bottom.stl

    396 Ko · 3 060 downloads

    Downloaden
  • stl

    Case_Foot_adjustable.stl

    949 Ko · 3 030 downloads

    Downloaden
  • stl

    PSU_Cover_Side.stl

    15 Ko · 3 052 downloads

    Downloaden
  • stl

    Reservoir_Holder.stl

    304 Ko · 3 046 downloads

    Downloaden
  • stl

    case_side_windowed.stl

    15 Ko · 3 053 downloads

    Downloaden
  • stl

    case_top.stl

    61 Ko · 3 068 downloads

    Downloaden
  • stl

    Power_Button.stl

    890 Ko · 3 041 downloads

    Downloaden
  • stl

    case_front.stl

    1.5 Mo · 3 072 downloads

    Downloaden
  • stl

    Pi_Board_Holder.stl

    602 Ko · 3 057 downloads

    Downloaden
  • stl

    case_side_solid_logo.stl

    2.9 Mo · 3 039 downloads

    Downloaden
  • stl

    case_side_solid.stl

    3.8 Mo · 3 039 downloads

    Downloaden
  • stl

    case_back.stl

    58.8 Mo · 3 080 downloads

    Downloaden
  • stl

    case_grill.stl

    102.8 Mo · 3 131 downloads

    Downloaden
  • stl

    SSD_2.stl

    1.1 Mo · 3 033 downloads

    Downloaden
  • stl

    PSU_Cover_Solid_Pi_3.stl

    187 Ko · 2 675 downloads

    Downloaden
  • stl

    case_back_Pi_3.stl

    4.4 Mo · 2 695 downloads

    Downloaden
  • stl

    USB_Passthrough_PSU_Cover_Cable.stl

    251 Ko · 1 961 downloads

    Downloaden
  • stl

    USB_Back_One_Slot.stl

    23.4 Mo · 1 959 downloads

    Downloaden
  • stl

    USB_Back_Two_Slot_2.stl

    23.1 Mo · 1 981 downloads

    Downloaden
  • stl

    USB_Back_Two_Slot_1.stl

    23.1 Mo · 1 969 downloads

    Downloaden
  • stl

    case_front_30x30mm_fans.stl

    5.7 Mo · 401 downloads

    Downloaden

Beschrijving

Raspberry Pi case based on a gaming rig.

UPDATE: Added front panel to support 30mmx30mm fans
casefront(30x30mm fans).stl

UPDATE: Added files to make this case accept a Pi 3
I do not have a Pi 3, so it is untested, but should work.
PSU_Cover_Solid_Pi_3.stl
case_back_Pi_3.stl

UPDATE: April 24th 2021 Added files for USB on back. Single and double

  • Rotating retractable feet.
  • Removable front screen with space for a filter.
  • Slide in side covers in both solid (with vent) or windowed (Rabbited for the thickness of an old CD case. Score one of the CD case panels with a razor and snap to shape)
  • Two PSU covers (what would be the PSU). One solid and one for a USB panel mount, so you can insert a USB Drive internally in the case. I soldered up an old USB DOM and printed a SSD like case for it (included if you're interested)
  • The back panel takes an RJ45 keystone jack like you would find at Home Depot. to extend the plug outside the case. (See images)
  • The power button takes a small microswitch glued into the power button housing. (See images) You will need to sand/cut to length.
  • There are two sets of feet, Solid and retracting. For the retracting, after inserting the foot into the peg, apply a tiny drop of glue to the center post and hold in place on the bottom of the case where you want the foot. I'd also wiggle the foot back and forth to keep it from gluing in place.
  • The Pi Board holder is much like an actual case. Mount the board to the board panel with tiny screws, and insert into the case. It aligns with notches that you might need to sand a little to fit.This design allows room for cables to be brought down to the bottom section.

Non printed parts

CAT5E connector

https://www.amazon.com/Vastercable-CAT5E-Keystone-Tooless-GREEN/dp/B00F5DX6JY/ref=sr_1_1?dchild=1&keywords=%22RJ45+keystone+jack%22&qid=1606756084&sr=8-1

RGB 40mm fans

https://smile.amazon.com/GeeekPi-Raspberry-40x40x10mm-Brushless-Multicolour/dp/B082X1W7M5/ref=sr_1_2?dchild=1&keywords=GeeekPi+RGB+5v&qid=1607732070&sr=8-2

Micro switch

https://www.amazon.com/microtivity-IM206-6x6x6mm-Tact-Switch/dp/B004RXKWI6/ref=sr_1_20?dchild=1&keywords=micro+tactile+push+button&qid=1606755944&s=electronics&sr=1-20

USB Extension cable : Watch the angle Left/Right check you case, board, etc...

https://www.amazon.com/Panel-Extension-Haokiang-Adapter-External/dp/B07NXXLBSK/ref=sr_1_5?dchild=1&keywords=USB+right+angle+panel&qid=1619289013&sr=8-5

NOTES:

  • I soldered a small breadboard to connect the three fans together and connected that to the Pi 5V connector
  • Power button is connected to 5 and 6 (GPIO3 and GND) for controlling the power search google for "Raspberry Pi button wake functionality"
  • This case fan combo pushes a lot of air and is a bit noisy. Great for a pi under full load, or you can connect the fans to 3.3v or use a resistor inline to slow them down. Not sure what that would do to the LED's though.
  • All parts printed on normal settings with 22% infill except the power button and the feet that were 100% infill.
  • Supports were needed. I'm sure you can figure out where they need to be,
  • The case is designed to glue together all five sections. [ case_top.stl, case_bottom.stl, case_front.stl, case_back.stl, and PSU_Cover_Side.stl] Use superglue or CA Glue.

In closing
This case took to much time to make and went through a lot of design changes but was super fun to make. I hope you like it.

Questions welcome.

Tags

#Gaming Case #Octoprint #pi 3 #pi 3 Case #Pi 4 #Pi 4 case #Pi Case #raspberry #raspberry 3 #Raspberry 4 #Raspberry Case #raspberry pi 4 #retro #Retrogaming #retropie