Etherfields Board Game Insert
por bdyer64
Ficheiros imprimíveis (59)
-
stlEFMaskl1Box.stl
43 Ko · 68 descargas
-
stlEFCoreTileCardsBox.stl
65 Ko · 67 descargas
-
stlEFCurrentDreamLargeDivider.stl
453 Ko · 66 descargas
-
stlEFFreeSpiritDivider.stl
310 Ko · 67 descargas
-
stlEFFateDivider.stl
164 Ko · 67 descargas
-
stlEFStorageDivider.stl
373 Ko · 66 descargas
-
stlEFDiscardMaker.stl
321 Ko · 66 descargas
-
stlEFToughGuyDivider.stl
318 Ko · 68 descargas
-
stlEFFlawsDivider.stl
196 Ko · 66 descargas
-
stlEFTurnsDivider.stl
204 Ko · 66 descargas
-
stlEFSecretCardsBox.stl
87 Ko · 69 descargas
-
stlEFBlankMarker.stl
21 Ko · 66 descargas
-
stlEFMarketsAndStorageLid.stl
793 Ko · 67 descargas
-
stlEFExpansionTileCardsBox.stl
65 Ko · 67 descargas
-
stlEFMask3Box.stl
43 Ko · 69 descargas
-
stlEFCurrentDreamSmallDivider.stl
453 Ko · 67 descargas
-
stlEFCoreTileCardsLid.stl
535 Ko · 66 descargas
-
stlEFMasks1Lid.stl
573 Ko · 67 descargas
-
stlEFSlumberDeclDivider.stl
424 Ko · 66 descargas
-
stlEFMinis3Lid.stl
751 Ko · 68 descargas
-
stlEFHandMarker.stl
196 Ko · 66 descargas
-
stlEFItemsMarketDivider.stl
217 Ko · 66 descargas
-
stlEFDeckMarker.stl
148 Ko · 66 descargas
-
stlEFOtherTokensLid.stl
565 Ko · 67 descargas
-
stl
EFMarkers1Box.stl
589 Ko · 67 descargas
-
stlEFInfluenceMarketDivider.stl
277 Ko · 67 descargas
-
stl
EFMarketsAndStorageBox.stl
65 Ko · 67 descargas
-
stlEFMask2Box.stl
43 Ko · 68 descargas
-
stlEFExpansionTileCardsLid.stl
658 Ko · 66 descargas
-
stl
EFMarkers1Lid.stl
609 Ko · 67 descargas
-
stlEFMarkers2Box.stl
589 Ko · 67 descargas
-
stlEFOtherSignsMiscBox.stl
219 Ko · 77 descargas
-
stlEFMask3Lid.stl
600 Ko · 69 descargas
-
stlEFMinis3Box.stl
44 Ko · 67 descargas
-
stlEFPlayerCardsBox.stl
65 Ko · 70 descargas
-
stlEFReaperDivider.stl
279 Ko · 67 descargas
-
stlEFRiddlerLid.stl
356 Ko · 66 descargas
-
stlEFMask2Lid.stl
590 Ko · 67 descargas
-
stlEFMinis1Box.stl
45 Ko · 69 descargas
-
stl
EFMarkers2Lid.stl
915 Ko · 68 descargas
-
stlEFOtherMarker.stl
192 Ko · 66 descargas
-
stlEFThornKnightDivider.stl
319 Ko · 66 descargas
-
stlEFProgressMarker.stl
389 Ko · 66 descargas
-
stlEFOtherSignsMiscLid.stl
925 Ko · 66 descargas
-
stl
EFPlayerSignsBox.stl
112 Ko · 68 descargas
-
stl
EFMinis2Box.stl
44 Ko · 70 descargas
-
stlEFRemovedTilesDivider.stl
278 Ko · 67 descargas
-
stlEFSlumberMapDivider.stl
458 Ko · 67 descargas
-
stlEFPlayerSignsLid.stl
630 Ko · 68 descargas
-
stlEFRiddlerBox.stl
44 Ko · 66 descargas
-
stlEFMinis2Lid.stl
842 Ko · 67 descargas
-
stlEFRemovedSecretsDivider.stl
278 Ko · 67 descargas
-
stl
EFOtherTokensBox.stl
274 Ko · 68 descargas
-
stlEFMinis1Lid.stl
1.1 Mo · 68 descargas
-
stlEFSpecialistDivider.stl
412 Ko · 66 descargas
-
stlEFPlayerCardsLid.stl
652 Ko · 67 descargas
-
stlEFSecretCardsLid.stl
930 Ko · 68 descargas
-
stlEFGamblerDivider.stl
316 Ko · 67 descargas
-
stlEFSeasonsDivider.stl
445 Ko · 67 descargas
Descrição
An insert for Etherfields. This insert will hold all the base content except the boss mini along with all the cards from all the expansions. It will not hold all the Scripts books (or the special plastic maps), but you only need one at a time anyway so you can swap the ones in that you need as you play through the campaigns. I put all the boss minis and the script books from the expansion campaigns in the stretch goals box.
I have replaced all the included dividers with printed dividers that are low profile to save a lot of space.
For each of the players there are a set of dividers that allow you to store away your deck and remember where everything was.
The minis rattle around a bit in the boxes so if you are worried use some foam or bubble wrap.
The inserts accomodate sleeved cards for the most part. It will not fit all the secrets cards sleeved, I sleeve these as they are put into play, otherwise they are left unsleeved. The square tile cards are not sleeved, not even sure if sleeve for these cards exist.
Printing parameters will depend on your printer, but I use a layer height of 0.2 mm, 4 layers bottom and top, a wall count of 4 and 30% infill. The boxes tend to pull up and warp on the corners so play around with our printer setting and first layer to make them stick. You can see in the pictures that I didn't total succeed in eliminationg all warping. Most of the time it is just aesthetic and doesn't effect the function.
To pack this into the box there are four layers with most of the content being in the first layer. See included pictures for how to pack.