Anet A8 Electronics Case
par billybob884
Fichiers imprimables (16)
-
stlcase_front_recessed_SD.STL
516 Ko · 7 429 téléchargements
-
stlcase_front_extruded_SD.STL
521 Ko · 7 408 téléchargements
-
stlcase_front_plain_SD.STL
452 Ko · 7 438 téléchargements
-
stlcase_front_recessed_MicroSD.STL
516 Ko · 7 422 téléchargements
-
stlcase_front_extruded_MicroSD.STL
521 Ko · 7 400 téléchargements
-
stlcase_front_plain_MicroSD.STL
452 Ko · 7 417 téléchargements
-
stlcase_back.STL
474 Ko · 7 443 téléchargements
-
stlcase_bottom.STL
775 Ko · 7 450 téléchargements
-
stlcase_frontplate_buttons.STL
161 Ko · 7 427 téléchargements
-
stlcase_frontplate_plain.STL
159 Ko · 7 423 téléchargements
-
stlcase_top_plain.STL
955 Ko · 7 404 téléchargements
-
stlcase_top_reset.STL
1010 Ko · 7 415 téléchargements
-
stlj-box.STL
60 Ko · 7 402 téléchargements
-
stlj-box_top.STL
4 Ko · 7 401 téléchargements
-
stlreset_button.STL
13 Ko · 7 391 téléchargements
-
stlbuttons.STL
223 Ko · 7 411 téléchargements
Description
This is a remix of https://www.thingiverse.com/thing:2742130
It's a fully self-contained electronics box for the Anet A8 -- it houses the main board, an upgraded 30A power supply, the LCD control board, two mosfets, includes ports for a USB and SD card extension cables, and a 12V 80mm fan.
I liked Jaro's original design, but it has some problems; several screw holes are poorly aligned, it's significantly oversized (mine is ~40% smaller), and it makes the reset button inaccessible. My redesign fixes all those problems.
I also made a few aesthetic changes, I added the option of a recessed/extruded ANET A8 logo, as well as the option to use an SD or MicroSD card reader extension port, and an LCD faceplate with and without graphical buttons.
Also included is a "junction box" that mounts on the side of the printer where the cable's can go.
You'll need some additional hardware to go with it:
80x80x25mm 12V Fan:
https://www.amazon.com/dp/B00N1Y50QQ/
3ft USB-B (F) to USB-B (M) Extension Cable:
https://www.amazon.com/dp/B00FSYBKPM/
12V,30A DC Power Supply (360W)
https://www.amazon.com/dp/B00D7CWSCG/
2x MOSFETs
https://www.amazon.com/dp/B06XY5HBFX/
Power Socket (10A,250V) w/ Switch & 5A Fuse
https://www.amazon.com/dp/B06XNMT3WL/
MicroSD to SD Card Extension Cable
https://www.amazon.com/dp/B06XY5QB2Z/
--Alternate--
MicroSD to MicroSD Card Extension Cable
https://www.amazon.com/dp/B072X27V58/
Optionally, I also chose to put little stick-on rubber feet on the bottom so it wouldn't slide around.
You'll also need to build some extension cables for the motors, end-stop switches, fans, and thermistor:
JST-XH Connector Kit (2.54mm Pitch)
https://www.amazon.com/dp/B07CH7ZTRB/
26AWG Electrical Wire
https://www.amazon.com/dp/B07G2LRX68/
I made mine 3ft (1m) long so I could move the box out of the way on my table. In case you're worried, voltage drop and increased resistance/inductance are negligible over a few feet, so there's no need to worry about that.